Ultra96

• 4x Cortex-A53, 2x Cortex-R5*, Mali-400MP2 GPU, Xilinx Zynq UltraScale+ FPGA

  • * ARM Cortex-R Series is a family of embedded processors for real-time systems

• 2 GB Memory

• MiniDP,1x USB 3.0 Micro-B,2x USB 3.0 A,1x USB 2.0,expansion headers

• 802.11b/g/n & Bluetooth 4.2 + BLE

• PetaLinux or bare-metal

• Power Supply: 12V @ 2A (Coaxial Connector 4.75mm / 1.7mm)

Availability

Total 4 Boards - 1 @ Yannick Bäumer - 1 @ Robert Schmid - 2 available

ALLNET ALL3073V2

• power plug switchable via HTTP requests
• 16 A / 3600 W
• available: 2 of 2

Parallella Board

• 16-core Epiphany RISC SOC

• Zynq SOC (FPGA + ARM A9)

• Gigabit Ethernet

• 1GB SDRAM

• Micro-SD storage

• Up to 48 GPIO pins

• HDMI, USB (optional)

• Cluster configuration: 4 Boards in a single case

  • Power Supply 5V @ 8A (3 Pin XLR Connector)

Availability

Total 1 cluster of 4 boards - 1 available

Agilent 34401A

digitales Tisch-Multimeter

• 0.1 – 750 VAC
• 0.1 – 1 kVDC
• 0.01 – 3 A AC
• 1 – 3 A DC
• 100 MΩ – 100 Ω
• 3 Hz – 300 kHz
• RS232-/GPIB-Schnittstelle
• available: 1 of 1

Agilent E3631A

Labornetzteil

• 0 – 6 / 0 – 25 VDC
• 0 – 5 / 0 – 1 A
• RS232-/GPIB-Schnittstelle
• available: 1 of 1

Arduino Nano

• ATmega328
• 16 MHz
• 32 KB flash
• 2 KB SRAM
• 1 KB EEPROM

Arduino Uno

• ATmega328P
• 16 MHz
• 32 KB flash
• 2 KB SRAM
• 1 KB EEPROM

ARIS-EDGE

• ARM Cortex-M0+ (up to 32 MHz, 128 kB Flash, 16 kB RAM)
• Bosch BNO055 (Smart 9-DOF IMU with sensor fusion and absolute orientation sensing)
• Bosch BME280 (accurate pressure, humidity, & temperature sensor)
• Silicon Labs MGM111 (multi-protocol RF module, supporting latest Thread, BLE, & ZigBee stacks)

Beckhoff SPS

• RPS 60 Hirschmann Rail-Power-Supply RPS-60 24V DC Hutschienen-Netzteil
• CX1100-0002 Stromversorgung mit K-Bus-Interface
• CX1100-0004 Stromversorgung mit E-Bus-Interface
• CX1000-0xxx CPU-Grundmodul
• CX1010-0xxx CPU-Grundmodul
• CX1000-N001 Systemschnittstelle (DVI/USB-Anschluss)
• CX1010-N010 Systemschnittstelle (DVI/USB-Anschluss)
• BK1120 EtherCAT-Buskoppler
• KL1104 4-Kanal-Digital-Eingangsklemme 24 V DC
• KL2612 2-Kanal Relais Ausgangsklemme 125 V AC (2x Wechsler)
• KL2134 4-Kanal-Digital-Ausgangsklemme 24 V DC
• KL9010 Busendklemme
• EL2004 4-Kanal-Digital-Ausgangsklemme 24 V DC, 0,5 A
• EL6001 Serielle Schnittstelle RS232
• EK1110 EtherCAT-Verlängerung

CCCamp 2015 rad1o Badge

• full-featured SDR (software defined radio) half-duplex transceiver (50 MHz - 4000 MHz)
• ARM Cortex M4 CPU
• Nokia 6100 130×130 pixel LCD
• 3.5 mm audio connector
• 2 micro USB ports
• joystick

Carrera D132 (Customized)

• off-the-shelf Carrera Digital 132 race-track including “Carrera control unit” extended with several additional position sensors
• various handcrafted sensor & actuator boards
• 8/16-bit AVR XMEGA A3 microcontroller, FT245R USB FIFO IC, RS232 interface, four RJ-12 interfaces, …
• self-driving car

Layout v2019

http://www.softyroyal.de/?t=c29b4e57 Länge Außen- und Innenbahn je 10,2842 m

• 1x 1/3 Gerade, 11,5cm
• 1x Boxengasse Ausfahrt
• 1x Boxengasse Einfahrt
• 5x Boxengasse Verlängerung
• 1x Control Unit
• 2x Doppelweiche (Teil 1)
• 2x Doppelweiche (Teil 2)
• 6x Kurve K1, Radius 39,6cm, 60°
• 6x Kurve K2, Radius 59,4cm, 30°
• 4x Kurve K3, Radius 79,2cm, 30°
• 2x Kurve K4, Radius 99,0cm, 15°
• 2x Randstreifen 1/3 Gerade
• 4x Randstreifen Endstück Links
• 3x Randstreifen Endstück Rechts
• 6x Randstreifen K1 außen, 60°
• 4x Randstreifen K1 innen, 60°
• 6x Randstreifen K2 außen, 30°
• 3x Randstreifen K2 innen, 30°
• 4x Randstreifen K3 außen, 30°
• 2x Randstreifen K3 innen, 30°
• 2x Randstreifen K4 außen, 15°
• 2x Randstreifen K4 innen, 15°
• 13x Randstreifen Standardgerade
• 3x Standardgerade, 34,5cm
• 1x Weiche links (Teil 1)
• 1x Weiche links (Teil 2)
• 1x Weiche rechts (Teil 1)
• 1x Weiche rechts (Teil 2)

Initial Layout

http://www.softyroyal.de/?t=39a1c26a

• 8x Standardgerade, 34,5cm
• 10x Kurve K1, Radius 39,6cm, 60°
• 5x Kurve K3, Radius 79,2cm, 30°
• 7x Kurve K2, Radius 59,4cm, 30°
• 1x Doppelweiche (Teil 1)
• 1x Doppelweiche (Teil 2)
• 6x Kurve K4, Radius 99,0cm, 15°
• 1x Weiche links (Teil 2)
• 1x Weiche links (Teil 1)
• 2x 1/3 Gerade, 11,5cm
• 2x 1/4 Gerade, 8,6cm
• 1x Weiche rechts (Teil 1)
• 1x Weiche rechts (Teil 2)
• 1x Boxengasse Einfahrt
• 1x Boxengasse Ausfahrt
• 4x Boxengasse Verlängerung
• 1x Control Unit
• 1x Aufstellung
• 6x Randstreifen K2 außen, 30°
• 10x Randstreifen K1 außen, 60°
• 11x Randstreifen Standardgerade
• 5x Randstreifen Endstück Rechts
• 2x Randstreifen 1/3 Gerade
• 6x Randstreifen K4 außen, 15°
• 5x Randstreifen K3 außen, 30°
• 2x Randstreifen K2 innen, 30°
• 5x Randstreifen Endstück Links
• 1x Randstreifen K4 innen, 15°
• 2x Randstreifen K1 innen, 60°

Elektro-Automatik EA-PS 5200-10 A

• 0 – 200 VDC 10 A
• 640 W max
• over voltage & over current protection
• available: 1 of 1
• switchable via USB (ModBus RTU)

Ettus USRP B210

Software-defined Radio

• Transceiver 70 MHz – 6 GHz
• Full duplex, MIMO (2 Tx & 2 Rx)
• USB 3.0
• reconfigurable Spartan 6 XC6SLX150 FPGA
• available: 0 of 2 (@ Paul G.)

HPE EL20

• HPE GL20 IoT Gateway (formerly HPE EL20 Intelligent Gateway)
• Intel Core i5 CPU
• 8GB RAM, 64 GB SDD Storage
• 4 PCI Express Mini-card slots
• 4 PoE ports, 8-bit DIO
• 9 to 36 Volts DC input

IMST Lite Gatway

• LoRaWAN gateway 868 MHz
• Raspberry Pi+B
• iC880A-SPI LoRaWAN Concentrator

Availability

One device, running as a gateway for https://thethingsnetwork.org .

Intel Edison (with Arduino Breakout)

• Intel Edison

• Intel SoC dual-core CPU

• Intel Atom CPU (500 MHz)

• 32-bit Intel Quark microcontroller (100 MHz)

• WiFi, Bluetooth LE, 70-pin connector

• 1 GB RAM

• 4 GB flash

• Yocto Linux* v1.6

• Arduino Breakout

• Arduino 1.0 pinout

• micro SD card connector

• 2x micro USB, 1x USB-A

• Power Supply 7-15V @ >1.5A (Coaxial Connector)

LEGO EV3

• TI Sitara AM1808 (ARM926EJ-S core)
• 300 MHz
• 64 MB RAM
• 16 MB Flash
• microSDHC Slot

Netgear R6120 W-LAN router

• AC1200
• dual band
• can run OpenWrt

Nvidia Jetson Nano

• 128-core Maxwell CPU

• Quad-core ARM A57 @ 1.43 GHz GPU

• 4 GB 64-bit LPDDR4 25.6 GB/s

• 1x MIPI CSI-2 DPHY lanes,

• Gigabit Ethernet, M.2 Key E

• HDMI 2.0 and eDP 1.4

• 4x USB 3.0, USB 2.0 Micro-B

• GPIO, I2C, I2S, SPI, UART

• Power Supply 5V @ 4A (Coaxial Connector 5.5mm/2.1mm)

Availability

Total 3 boards - 1@Daniel? - 2@HPI

Nvidia Jetson TX2

• NVIDIA Pascal Architecture GPU

• 2 Denver 64-bit CPUs + Quad-Core A57 Complex

• 8 GB L128 bit DDR4 Memory

• 32 GB eMMC 5.1 Flash Storage

• 802.11ac Wi-Fi, Bluetooth

• 10/100/1000BASE-T Ethernet

• USB 3.0 Type A, USB 2.0 Micro AB, HDMI, M.2 Key E, PCI-E x4, Gigabit Ethernet, Full-Size SD, SATA Data and - Power, GPIOs, I2C, I2S, SPI, CAN, TTL UART, Display + Camera Expansion

• Power Supply 19.5V @ 4.5A (Coaxial Connector)

Availability

Total 1 board - 1 available

ODROID-C2

• 64-bit quad-core single board computer (SBC)

• ARM Cortex-A53(ARMv8) 1.5Ghz quad core CPUs 

• Mali-450 GPU

• 2 GB RAM

• 40pin GPIOs + 7pin I2S

• Mint Linux 16.04 (64 bit)

• 4x USB 2.0, 1x USB OTG, Gigabit Ethernet, HDMI, IR Receiver, Flash Storageslot, MicroSD Card slot

• Power Supply 5V @ 2A (MicroUSB or Coaxial Connector 2.5mm/0.8mm)

Availability

Total 2 Boards - 2 available

ODROID-C4

• 64 bit quad-core single board computer (SBC)

• ARM Cortex-A55 (ARMv8-A) 2 GHz quad-core CPU

• Mali-G31 GPU

• 4 GB DDR4

• 40-pin GPIOs + 7pin I2S

• 4 x USB 3.0, 1 x Micro-USB 2.0 OTG, Gigabit Ethernet, HDMI, IR Receiver, eMMC module socket, Micro SD Card slot

• Power Supply 12 V @ 2 A (MicroUSB or Coaxial Connector 2.5mm/0.8mm)

Availability

Odroid XU4 – ARM big.LITTLE

• Samsung Exynos5422 Cortex-A15 2Ghz & Cortex-A7 Octa core CPUs

• Mali-T628 MP6 (OpenGL & OpenCL)

• 2 GB RAM

• Flash Storage

• 2 x USB 3.0, 1 x USB 2.0, Gigabit Ethernet, HDMI

• Mint Linux 16.04

• Power Supply 5V @ 4A (Coaxial Connector 5.5mm/2.1mm)

Availability

Total 4 Boards - 4 available

Raspberry Pi 3 (A+ & Zero W)

• CSI, Audio, microSD, GPIO (40 Pin), no LAN
• 512 MB DDR2-RAM
• 1,4 GHz ARM Cortex-A53 Quad-Core-CPU 8
• WLAN 802.11 b/g/n/ac, BT 4.2
• HDMI, 1x USB 2.0

Raspberry Pi 3 B+

• 1024 MB DDR2-RAM
• 1,4 GHz ARM Cortex-A53 Quad-Core-CPU
• WLAN 802.11 b/g/n/ac (2,4 + 5,0 GHz)
• LAN RJ45 10/100/1000 Mbit

Raspberry Pi 3 B

• 1024 MB DDR2-RAM
• 1,2 GHz ARM Cortex-A53 Quad-Core-CPU
• WLAN 802.11 b/g/n
• LAN RJ45 10/100 Mbit

Raspberry Pi 3 Zero W

• CSI, Audio, microSD, GPIO (40 Pin), no LAN
• 512 MB DDR2-RAM
• 1,0 GHz BCM2853
• WLAN 802.11 b/g/n, BT 4.1
• mini-HDMI, 2x micro-USB

Raspberry Pi 4 (Model B)

• 1,5 GHz ARM Cortex-A72Quad-Core-CPU
• 4 GB LPDDR4 SDRAM
• Gigabit LAN RJ45,
• Bluetooth 5.0
• 2x USB 2.0 / 2x USB 3.0
• 5V/3A @ USB Typ- C
• 2x microHDMI (1x 4k @60fps oder 2x 4k @30fps) H.265/H.264

Rock Pi S

• Rockchip RK3308 Quad A35 64bit CPU with built-in Voice Activity Detection (VAD)
• USB 2.0 OTG (Typ C) + USB 2.0 HOST (Typ A)
• 512 MB RAM
• RJ45 10/100Mbit Ethernet
• 802.11 b/g/n Wifi, Bluetooth 4.0external antenna connector
• 26 pin GPIO header
• 26 pin voice/audio header includes I2S, PCM, TDM, PDM, SPDIF, and HDMI ARC

TP-Link Archer C7

• AC1750
• dual band
• can run OpenWrt